AMF
X
group picture
group picture

Support Element, cartridge flange

Normally retracted. Hydraulic advanced. Spring force for contact,
max. operating pressure 70 bar,
min. operating pressure 25 bar.

Order
no.		 Article no. Contact force F1
[N] 		Support force at 70 bar
[kN] 		Stroke H
[mm] 		Vol.
[cm³] 		Md max.
[Nm] 		Md 1 max.
[Nm] 		Q max.
[l/min] 		Weight
[g] 		CAD SC
552200 6944EH-03-2 2,8 - 3,8 3,0 6,5 0,8 32 5,4 2,5 198
559184 6944EH-03-5 3,7 - 5,5 3,0 6,5 0,8 32 5,4 2,5 198
552201 6944EH-04-2 3,6 - 5,6 4,0 8,0 1,4 50 10,0 2,5 280
559185 6944EH-04-5 4,7 - 7,8 4,0 8,0 1,4 50 10,0 2,5 280
552202 6944EH-05-2 4,7 - 7,8 5,5 8,0 1,5 63 16,5 2,5 378
559186 6944EH-05-5 6,2 - 11,0 5,5 8,0 1,5 63 16,5 2,5 378
552203 6944EH-10-2 5,8 - 9,7 10,0 10,0 1,8 80 30,0 2,5 719
559187 6944EH-10-5 7,9 - 13,6 10,0 10,0 1,8 80 30,0 2,5 719

Design:

Body made from steel, tempered and burnished. Support pin with internal thread case hardened and ground. Wiper to protect against dirt and cooling water. Oil supply via oil channel in fixture body.

Application:

The support element is used as an extra support to prevent sagging and vibration of a workpiece.

Features:

Element with high load capacity and low height. Oil pressure: The plunger is retracted in the normal position. When pressure is applied, the support pin advances with a weak spring-applied force against the inserted workpiece. The spring force varies with the pin stroke. As the hydraulic pressure rises, the support pin is hydraulically clamped. When the pressure is released, the support pin returns to the normal position. Very high support force ensures optimum manufacturing quality.

Note:

The support pin must be protected against the entry of dirt and splash water by a set screw. When putting into operation, make sure that the hydraulic system is vented perfectly. Failure to do so can cause destruction of the clamping element by the escaping diesel effect. The vent hole must be connected. No coolant must be sucked through this.

The supporting force should be matched to the clamping force in order to absorb machining forces.
The supporting force should always be at least twice as high as the clamping force.

  • dimensions table
    Order
    no.     		Article no. A B C dia. D
    		 E F G dia. J K L dia. N dia. P SW SW1 SW2 SW3 OR-1
    O-ring
    Order No.     		OR-2
    O-ring
    Order No.
    552200 6944EH-03-2 57 9,0 7,4 10 7,6 1,7 M26 x 1,5 9,0 3,0 66,0 24,1 9,5 24 8 13 8 552156 552153
    559184 6944EH-03-5 57 9,0 7,4 10 7,6 1,7 M26 x 1,5 9,0 3,0 66,0 24,1 9,5 24 8 13 8 552156 552153
    552201 6944EH-04-2 62 10,5 9,4 12 10,3 1,7 M30 x 1,5 11,5 3,5 72,5 28,2 11,5 27 10 15 10 159400 128660
    559185 6944EH-04-5 62 10,5 9,4 12 10,3 1,7 M30 x 1,5 11,5 3,5 72,5 28,2 11,5 27 10 15 10 159400 128660
    552202 6944EH-05-2 58 11,0 8,4 15 8,3 1,8 M36 x 1,5 12,5 4,0 69,0 34,2 14,5 32 13 19 11 552469 175216
    559186 6944EH-05-5 58 11,0 8,4 15 8,3 1,8 M36 x 1,5 12,5 4,0 69,0 34,2 14,5 32 13 19 11 552469 175216
    552203 6944EH-10-2 71 11,0 9,0 16 11,0 1,8 M45 x 1,5 12,5 4,0 82,0 43,1 15,5 41 13 21 11 552612 240309
    559187 6944EH-10-5 71 11,0 9,0 16 11,0 1,8 M45 x 1,5 12,5 4,0 82,0 43,1 15,5 41 13 21 11 552612 240309

    Order
    no.     		Article no. dia. a dia. b Øc
    max.
    		 e f g h k l dia. n Øp
    max.
    		 r
    552200 6944EH-03-2 24,5 27 2,5 3 8,5 M26 x 1,5 1 0,7 16-47 24,2 8 9,4
    559184 6944EH-03-5 24,5 27 2,5 3 8,5 M26 x 1,5 1 0,7 16-47 24,2 8 9,4
    552201 6944EH-04-2 28,5 31 2,5 3 11,0 M30 x 1,5 1 0,7 17-50 28,3 10 10,9
    559185 6944EH-04-5 28,5 31 2,5 3 11,0 M30 x 1,5 1 0,7 17-50 28,3 10 10,9
    552202 6944EH-05-2 34,5 37 4,5 3 10,5 M36 x 1,5 1 0,7 18-48 34,3 10 13,5
    559186 6944EH-05-5 34,5 37 4,5 3 10,5 M36 x 1,5 1 0,7 18-48 34,3 10 13,5
    552203 6944EH-10-2 43,5 46 5,0 3 10,5 M45 x 1,5 1 0,7 21-58 43,2 12 17,0
    559187 6944EH-10-5 43,5 46 5,0 3 10,5 M45 x 1,5 1 0,7 21-58 43,2 12 17,0

    Order
    no.     		Article no. BB dia. CC DD EE dia. FF GG dia. JJ OR-3
    O-ring
    Order No.     		max. permitted weight
    of the set screw
    [g]
    552200 6944EH-03-2 5,0 4,5 1,93 0,5 3,5 M6 9,0 552155 85
    559184 6944EH-03-5 5,0 4,5 1,93 0,5 3,5 M6 9,0 552155 110
    552201 6944EH-04-2 4,8 6,2 1,8 0,7 4,9 M8 11,5 552245 110
    559185 6944EH-04-5 4,8 6,2 1,8 0,7 4,9 M8 11,5 552245 140
    552202 6944EH-05-2 9,0 8,2 2,5 1,0 5,9 M10 12,5 552174 140
    559186 6944EH-05-5 9,0 8,2 2,5 1,0 5,9 M10 12,5 552174 185
    552203 6944EH-10-2 9,0 8,2 2,5 1,0 5,9 M10 12,5 552174 175
    559187 6944EH-10-5 9,0 8,2 2,5 1,0 5,9 M10 12,5 552174 235

    Always consider the permitted total weight of the set screw for in-house production.