AMF
X
group picture
group picture

Vertical Clamp

Double-acting,
max. working pressure 250 bar,
min. operating pressure 25 bar.

Order
no.
Article no. Clamping force F1
at 100 bar
[kN]
Clamping force F1
at 250 bar
[kN]
Piston force F5
at 100 bar
[kN]
Piston force F5 at 250 bar
[kN]
Vol. Sp
[cm³]
Vol. Lo
[cm³]
eff. piston
area Sp
[cm²]
eff. piston
area Lo
[cm²]
Md max.
[Nm]
Q max.
[l/min]
Weight
[g]
CAD SC
553427 6958DT-12 0,7 1,8 1,1 2,8 0,9 0,5 1,1 0,6 2,7 0,3 175
326231 6958DT-16 1,3 3,3 2,0 5,0 2,0 1,2 2,0 1,2 7,5 0,5 365
326298 6958DT-20 2,1 5,2 3,1 7,8 3,8 2,4 3,1 2,0 15,0 0,8 386
326397 6958DT-25 3,2 8,2 4,9 12,2 6,9 4,1 4,9 2,9 27,0 1,2 1015
327510 6958DT-32 5,3 13,4 8,0 20,1 13,7 8,3 8,0 4,9 47,0 2,0 1970

Sp = clamp, Lo = unclamp

Design:

Hydraulic cylinder as a drop-in cartridge. Top mounting with four cylinder screws (resistance min. 10.9); these are supplied as standard. All components are made from hardened, tempered and burnished steel. Piston and pivot bolts are made from tempered steel, hardened and nitrided. Metal wiper to protect the dirt wiper is integrated into the housing. Compressed air nozzle for pneumatic clamping control. Pivot bolts, tensioning straps and compressed air nozzle are supplied as standard, but not clamping arms. Oil supply via oil channel in fixture body.

Application:

The double-acting vertical clamp is highly suited to clamping in clamping pockets. For clearly defined return movements.

Features:

Small dimensions, can be positioned close to the workpiece. Clamping levers easy to change with built-in vertical clamp. The horizontal centre axis at the clamping lever and the pressure point on the workpiece lie in one plane. This prevents relative movement on the workpiece. To protect the O-rings sitting radially on the clamp, the cross channels at the installation hole must be rotated freely and equipped with insertion lead-ins. If the vertical clamp is closed, the compressed air that previously streamed out freely is blocked in the compressed air nozzle. The resulting back pressure can be used for clamping control with the help of a signal converter.

Note:

The signal converter is not included in the supply scope.
The lever ratio B to C is 1 to 1.5 for the standard levers!
In preparing the blank levers, deviations that cause a higher clamping force are permitted only in exceptional cases.

  • dimensions table
    Order
    no.
    Article no. A A1 B C E dia. D
    H H1 H2 H3 H4 H5 H6 H7 K L M N P R S S1 V V1 V2 W ØZ OR-1
    O-ring
    Order No.
    553427 6958DT-12 49,5 0,13 10 15,0 17,0 18 13,5 47,7 31,0 38,0 22,0 7 16,0 12,2 20 28,5 10,0 4,5 10 8,5 50,1 23,55 20 7 11,4 36 4,5 409953
    326231 6958DT-16 51,9 0,40 12 18,0 19,0 24 16,5 58,4 38,3 46,3 27,0 11 19,3 11 26 33 10,5 5,5 12 11,5 68,3 37,49 29 15 13,7 51 6,5 497461
    326298 6958DT-20 54,0 1,25 14 21,0 23,0 30 20,3 73,2 49,0 59,0 34,0 14 25,0 16 32 40 13,0 6,0 16 14,0 78,9 41,60 33 15 17,5 59 8,5 490342
    326397 6958DT-25 51,2 0,70 17 25,5 27,5 35 21,0 79,4 51,0 62,0 37,0 12 27,0 16 39 51 16,0 8,0 20 19,0 96,1 48,55 39 15 21,0 71 10,5 321018
    327510 6958DT-32 53,4 -1,0 20 30,0 33,0 42 24,0 97,1 63,0 76,0 59,5 13 35,0 18 50 58 18,0 9,0 26 22,0 112,25 58,16 48 15 24,0 84 12,5 409748

    Order
    no.
    Article no. dia. D H7 dia. F G x T H10 J M R V V1 V2 W dia. X
    X1 dia. Y Y1
    553427 6958DT-12 18 19,4 M4x8 22,0 0,5 10,0 8,5 20 7 11,4 36 4 8 4 20,0
    326231 6958DT-16 24 25,4 M6x15 27,0 2,0 10,5 11,5 29 15 13,7 51 5 11 5 24,5
    326298 6958DT-20 30 31,4 M8x16 34,0 2,0 13,0 14,0 33 15 17,5 59 5 13 5 31,5
    326397 6958DT-25 35 36,4 M10x20 37,0 2,0 16,0 19,0 39 15 21,0 71 5 14 5 34,5
    327510 6958DT-32 42 43,4 M12x20 59,5 2,5 18,0 22,0 48 15 24,0 84 6 18 6 56,5