AMF
X

Built-in coupling nipple

Order
no.
Article no. for coupling
under pressure
for pressure-free coupling
Nominal
bore
[NW]
max. operating
pressure
[bar]
Coupling stroke
[mm]
Weight
[g]
CAD SC
525188 6989NE-03-01 - 3 350 4,5 21
328674 6989NE-03-02 - 3 350 4,5 21
328690 6989NE-05-01 - 5 500 4,5 25
328450 6989NE-05-01-01 - 5 500 4,5 45
445049 6989NE-05-02 - 5 500 4,5 25
328757 6989NE-05-02-01 - 5 500 4,5 45
328716 6989NE-08-01 - 8 300 7,0 60
328732 6989NE-08-02 - 8 300 7,0 60

Design:

Cylinder body and internal parts made of stainless steel. Seals from NBR, Viton, POM and PU.

Application:

Couplings are used for the leakage-free connection of hydraulic oil supplies. The coupling elements are installed in a body. The sealing between coupling mechanism and nipple is axial, and installed in the coupling mechanism. If the seal is worn, it can be replaced. The coupling mechanism must always be used in combination with a nipple of the same system. Depending on the version, the couplings can be connected and disconnected at the maximum working pressure. When installed in a tank line, a coupling nipple with pressure relief must be selected. This limits the pressure that can be built up in the uncoupled state (for example due to internal leakage of the clamping elements) to approx 5 bar. When the two parts of the coupling are engaged, the pressure relief is no longer active.

Features:

For connection, the coupling mechanism and nipple must be axially aligned. The bodies of the two parts must be guided when the axial sealing surfaces are ca. 2-3 mm apart. The radial position tolerance must not be exceeded. The separating force due to hydraulic pressure is given by the formula NW3: F [N] = 9,4 x p [bar], NW5: F [N] = 15,4 x p [bar], NW8: F [N] = 31,4 x p [bar]. This separating force must be countered by some external, mechanical means. The coupling mechanism must seal at the bottom of the hole in which it is installed. The mounting hole must be machined to the specified accuracy and surface finish.

Note:

The axial sealing surfaces must be protected from dirt. Because the coupling elements have smooth, uninterrupted sealing surfaces, the danger of them collecting dirt is reduced, and the ease with which the user can clean them before the joint is made is increased. Good results can be achieved by washing them off and blowing clean with compressed air.
Positioning tolerance in axial direction for all coupling elements: +0.5 mm.
Positioning tolerance in radial direction for coupling elements: +/- 0.3 mm.
Permissible angle tolerance: +/- 1°.

On request:

Other sizes available on request.

  • dimensions table
    Order
    no.
    Article no. dia. A dia. B
    C D G dia. H K L M dia. N
    525188 6989NE-03-01 13 16 10,0 11,4 25,9 9,8 10,0 4,5 15 5
    328674 6989NE-03-02 13 16 10,0 11,4 25,9 9,8 10,0 4,5 15 5
    328690 6989NE-05-01 16 20 10,0 11,4 26,0 13,5 10,0 4,5 15 5
    328450 6989NE-05-01-01 16 20 16,5 17,0 38,1 13,5 16,5 4,5 22 5
    445049 6989NE-05-02 16 20 10,0 11,4 26,0 13,5 10,0 4,5 15 5
    328757 6989NE-05-02-01 16 20 16,5 17,0 38,1 13,5 16,5 4,5 22 5
    328716 6989NE-08-01 21 24 9,0 15,0 31,4 18,5 9,0 7,4 15 10
    328732 6989NE-08-02 21 24 9,0 15,0 31,4 18,5 9,0 7,4 15 10