AMF
X
group picture
group picture

Bore clamp, hydraulic, eccentric

Single-acting, with spring return,
max. operating pressure 150 bar,
min. operating pressure 30 bar.
lateral compensation per clamp ± 0.25 mm.

Order
no.		 Article no. Clamping force
vertical
[kN] 		Clamping rim height min.
[mm] 		dia. K
[mm] 		L Weight
[g] 		CAD SC
63669 6970-07-50 3,5 6 6,8-7,7 10 2600
60798 6970-08-50 3,5 6 7,8-8,7 10 2600
63685 6970-09-50 5,3 7 8,8-9,7 10 2600
60814 6970-10-50 5,3 7 9,8-10,7 10 2800
63701 6970-11-50 8,5 8 10,8-11,7 13 2800
60830 6970-12-50 8,5 8 11,8-12,7 13 2800
63727 6970-13-50 11,5 9 12,8-13,7 13 2900
60822 6970-14-50 11,5 9 13,8-14,7 13 2900

Design:

The actuating piston is single-acting. Cylinder body, clamping segments and tensioning bolts are from hardened steel, gas-nitrided. Four-part clamping segments are externally serrated.
A Ø 8 H7 centring hole located on the underside for positioning the clamping element. Three fastening screws are included in the supply scope. Oil supply via threaded connection or oil channel in the fixture body.

Application:

The hydraulic bore clamp is preferred for use on workpieces with complex external geometries that must be clamped for machining. After the clamping segments engage into clamping holes attached on one side with low depth, reliable 5-sided machining does not present a problem.
Workpieces can be installed or removed automatically with handling devices.

Features:

The tension bolt has the shape of a four-sided pyramid at the coupling point to the clamping sleeve. The clamping sleeve segments have this shape also, thus ensuring contact on the entire surface in every position of the tension bolt.
This facilitates a high clamping force and ensures very low wear.
Elastic rings hold the clamping segments together and seal them against entry of chips. Depending on the material, the external serration is pressed into the clamping hole with more or less force, thus permitting the required positive fit. The built-in plate springs achieve a maximum pull-down stroke of approx. 0.2 mm.

The tension bolt has a pyramid shape for improved pre-centring of workpieces.

The bore clamp is also a contact surface for the workpiece. The workpiece contact surface is hard-metal coated (µ 0.3), thereby significantly increasing the displacement force.

The eccentric arrangement of the clamping elements is especially suited for clamping workpieces with circumferential contact edge, such as gear and engine housings, oil pans and similar workpieces.

Note:

The lateral force when inserting the workpiece must not exceed the "lateral force" table value. The radial force must be observed.

Please check with us for clamping hardened workpieces or those from GG / GGG.

On request:

Bore clamps for other hole diameters available upon request.

  • dimensions table
    Order
    no.     		Article no. Permissible
    horizontal force
    [kN]     		Radial force of
    sleeve segments
    [kN]     		Expansion
    of sleeve
    [mm]     		Piston
    dia.
    [mm]     		Vol.
    [cm³]     		Side load
    (unclamped)
    [N]     		A B ±0.01 C D dia. E dia. F dia. H dia. P OR-1
    O-ring
    Order No.
    63669 6970-07-50 1,0 10 1,4 18 1,0 50 59 75 9,5 6,6 24 9 80 15 260448
    60798 6970-08-50 1,0 10 1,4 18 1,0 50 59 75 9,5 7,5 24 9 80 15 260448
    63685 6970-09-50 1,5 15 1,4 22 1,5 80 59 75 9,5 8,5 24 9 80 15 260448
    60814 6970-10-50 1,5 15 1,4 22 1,5 80 59 75 9,5 9,5 24 9 80 15 260448
    63701 6970-11-50 2,5 25 1,4 28 2,5 120 59 75 12 10,5 24 9 80 19 260448
    60830 6970-12-50 2,5 25 1,4 28 2,5 120 59 75 12 11,5 24 9 80 19 260448
    63727 6970-13-50 3,5 35 1,4 32 3,2 150 59 75 12 12,5 24 9 80 19 260448
    60822 6970-14-50 3,5 35 1,4 32 3,2 150 59 75 12 13,5 24 9 80 19 260448